'stk200'에 해당되는 글 2건

  1. 2009.05.27 ubuntu에서 gnome-avrdude 사용하기
  2. 2009.04.20 STK-200 / STK-500 호환 AVR ISP (2)
ubuntu에는
/dev/paraport0 가 아닌
/dev/parport0 로 장치명이 되어 있었다.



그리고 그냥 패널에서 실행할경우 일반 사용자 모드로 구동이 되므로
아래와 같이 device를 열 수 없다는 에러가 발생한다.

패널에서 실행방법을 변경하거나
아니면 콘솔에서
$ sudo gnome-avrdude &
로 실행을 하면 해결이 된다.



패러럴로 사용시 stk200으로 프로그래머를 설정해주면
ATMega128을 패러럴로 읽을 수 있다.
신고
Posted by 구차니

댓글을 달아 주세요

패러럴이면 STK-200 호환
USB면 STK-500 호환이라고 한다.


Valid programmers are:
  c2n232i  = serial port banging, reset=dtr sck=!rts mosi=!txd miso=!cts [/usr/local/etc/avrdude.conf:834]
  dasa3    = serial port banging, reset=!dtr sck=rts mosi=txd miso=cts [/usr/local/etc/avrdude.conf:821]
  dasa     = serial port banging, reset=rts sck=dtr mosi=txd miso=cts [/usr/local/etc/avrdude.conf:808]
  siprog   = Lancos SI-Prog <http://www.lancos.com/siprogsch.html> [/usr/local/etc/avrdude.conf:795]
  ponyser  = design ponyprog serial, reset=!txd sck=rts mosi=dtr miso=cts [/usr/local/etc/avrdude.conf:782]
  89isp    = Atmel at89isp cable            [/usr/local/etc/avrdude.conf:749]
  frank-stk200 = Frank STK200                   [/usr/local/etc/avrdude.conf:735]
  blaster  = Altera ByteBlaster             [/usr/local/etc/avrdude.conf:722]
  ere-isp-avr = ERE ISP-AVR <http://www.ere.co.th/download/sch050713.pdf> [/usr/local/etc/avrdude.conf:712]
  atisp    = AT-ISP V1.1 programming cable for AVR-SDK1 from <http://micro-research.co.th/>  [/usr/local/etc/avrdude.conf:702]
  dapa     = Direct AVR Parallel Access cable [/usr/local/etc/avrdude.conf:691]
  xil      = Xilinx JTAG cable              [/usr/local/etc/avrdude.conf:678]
  futurlec = Futurlec.com programming cable. [/usr/local/etc/avrdude.conf:661]
  abcmini  = ABCmini Board, aka Dick Smith HOTCHIP [/usr/local/etc/avrdude.conf:651]
  picoweb  = Picoweb Programming Cable, http://www.picoweb.net/ [/usr/local/etc/avrdude.conf:641]
  sp12     = Steve Bolt's Programmer        [/usr/local/etc/avrdude.conf:630]
  alf      = Nightshade ALF-PgmAVR, http://nightshade.homeip.net/ [/usr/local/etc/avrdude.conf:614]
  bascom   = Bascom SAMPLE programming cable [/usr/local/etc/avrdude.conf:604]
  dt006    = Dontronics DT006               [/usr/local/etc/avrdude.conf:594]
  pony-stk200 = Pony Prog STK200               [/usr/local/etc/avrdude.conf:582]
  stk200   = STK200                         [/usr/local/etc/avrdude.conf:566]
  bsd      = Brian Dean's Programmer, http://www.bsdhome.com/avrdude/ [/usr/local/etc/avrdude.conf:555]
  pavr     = Jason Kyle's pAVR Serial Programmer [/usr/local/etc/avrdude.conf:547]
  dragon_dw = Atmel AVR Dragon in debugWire mode [/usr/local/etc/avrdude.conf:540]
  dragon_hvsp = Atmel AVR Dragon in HVSP mode  [/usr/local/etc/avrdude.conf:532]
  dragon_pp = Atmel AVR Dragon in PP mode    [/usr/local/etc/avrdude.conf:524]
  dragon_isp = Atmel AVR Dragon in ISP mode   [/usr/local/etc/avrdude.conf:516]
  dragon_jtag = Atmel AVR Dragon in JTAG mode  [/usr/local/etc/avrdude.conf:508]
  jtag2dw  = Atmel JTAG ICE mkII in debugWire mode [/usr/local/etc/avrdude.conf:500]
  jtag2isp = Atmel JTAG ICE mkII in ISP mode [/usr/local/etc/avrdude.conf:492]
  jtag2    = Atmel JTAG ICE mkII            [/usr/local/etc/avrdude.conf:484]
  jtag2fast = Atmel JTAG ICE mkII            [/usr/local/etc/avrdude.conf:476]
  jtag2slow = Atmel JTAG ICE mkII            [/usr/local/etc/avrdude.conf:468]
  jtagmkII = Atmel JTAG ICE mkII            [/usr/local/etc/avrdude.conf:460]
  jtag1slow = Atmel JTAG ICE (mkI)           [/usr/local/etc/avrdude.conf:453]
  jtag1    = Atmel JTAG ICE (mkI)           [/usr/local/etc/avrdude.conf:445]
  jtagmkI  = Atmel JTAG ICE (mkI)           [/usr/local/etc/avrdude.conf:437]
  avr911   = Atmel AppNote AVR911 AVROSP    [/usr/local/etc/avrdude.conf:431]
  avr109   = Atmel AppNote AVR109 Boot Loader [/usr/local/etc/avrdude.conf:425]
  butterfly = Atmel Butterfly Development Board [/usr/local/etc/avrdude.conf:419]
  usbtiny  = USBtiny simple USB programmer, http://www.ladyada.net/make/usbtinyisp/ [/usr/local/etc/avrdude.conf:413]
  usbasp   = USBasp, http://www.fischl.de/usbasp/ [/usr/local/etc/avrdude.conf:407]
  avr910   = Atmel Low Cost Serial Programmer [/usr/local/etc/avrdude.conf:401]
  stk600hvsp = Atmel STK600 in high-voltage serial programming mode [/usr/local/etc/avrdude.conf:395]
  stk600pp = Atmel STK600 in parallel programming mode [/usr/local/etc/avrdude.conf:389]
  stk600   = Atmel STK600                   [/usr/local/etc/avrdude.conf:383]
  stk500hvsp = Atmel STK500 V2 in high-voltage serial programming mode [/usr/local/etc/avrdude.conf:377]
  stk500pp = Atmel STK500 V2 in parallel programming mode [/usr/local/etc/avrdude.conf:371]
  stk500v2 = Atmel STK500 Version 2.x firmware [/usr/local/etc/avrdude.conf:365]
  mib510   = Crossbow MIB510 programming board [/usr/local/etc/avrdude.conf:359]
  stk500v1 = Atmel STK500 Version 1.x firmware [/usr/local/etc/avrdude.conf:353]
  stk500   = Atmel STK500                   [/usr/local/etc/avrdude.conf:347]
  avrisp2  = Atmel AVR ISP mkII             [/usr/local/etc/avrdude.conf:337]
  avrispmkII = Atmel AVR ISP mkII             [/usr/local/etc/avrdude.conf:331]
  avrispv2 = Atmel AVR ISP V2               [/usr/local/etc/avrdude.conf:325]
  avrisp   = Atmel AVR ISP                  [/usr/local/etc/avrdude.conf:319]
  arduino  = Arduino                        [/usr/local/etc/avrdude.conf:313]



신고
Posted by 구차니

댓글을 달아 주세요

  1. STK를 SKT로 잘못 읽고 핸드폰 이야긴 줄 알고 한참 살펴본 1인

    2009.04.21 02:14 신고 [ ADDR : EDIT/ DEL : REPLY ]