embeded/raspberry pi2020. 5. 16. 10:00

ht_capab 에서 HT40으로 되어있어서 에러가 나던데

일단은 conf 파일 예제에 있던 대로 HT40- 으로 하니 문제없이 작동하긴 한다.

ht_capab=[HT40-][SHORT-GI-20][SHORT-GI-40]

[링크 : https://w1.fi/cgit/hostap/plain/hostapd/hostapd.conf]

 

로그를 분석해보니 HT40이 문제가 아니었군

 5월 16 09:46:44 raspberrypi kernel: WARN::dwc_otg_hcd_urb_dequeue:639: Timed out waiting for FSM NP transfer to complete on 0
 5월 16 09:46:45 raspberrypi kernel: IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
 5월 16 09:46:45 raspberrypi hostapd[1455]: Driver does not support configured HT capability [DSSS_CCK-40]
 5월 16 09:46:45 raspberrypi hostapd[1455]: wlan0: interface state UNINITIALIZED->DISABLED
 5월 16 09:46:45 raspberrypi hostapd[1455]: wlan0: AP-DISABLED
 5월 16 09:46:45 raspberrypi hostapd[1455]: wlan0: Unable to setup interface.
 5월 16 09:46:45 raspberrypi hostapd[1455]: wlan0: interface state DISABLED->DISABLED
 5월 16 09:46:45 raspberrypi hostapd[1455]: wlan0: AP-DISABLED
 5월 16 09:46:45 raspberrypi hostapd[1455]: wlan0: CTRL-EVENT-TERMINATING
 5월 16 09:46:45 raspberrypi hostapd[1455]: hostapd_free_hapd_data: Interface wlan0 wasn't started
 5월 16 09:46:45 raspberrypi hostapd[1455]: nl80211: deinit ifname=wlan0 disabled_11b_rates=0
 5월 16 09:46:45 raspberrypi kernel: WARN::dwc_otg_hcd_urb_dequeue:639: Timed out waiting for FSM NP transfer to complete on 7
 5월 16 09:46:45 raspberrypi systemd[1]: hostapd.service: Control process exited, code=exited, status=1/FAILURE

 

iwlist 명령을 통해서 capability를 볼 수 있는 듯

$ iw list
Wiphy phy0
        max # scan SSIDs: 4
        max scan IEs length: 2257 bytes
        max # sched scan SSIDs: 0
        max # match sets: 0
        max # scan plans: 1
        max scan plan interval: -1
        max scan plan iterations: 0
        Retry short long limit: 2
        Coverage class: 0 (up to 0m)
        Device supports RSN-IBSS.
        Supported Ciphers:
                * WEP40 (00-0f-ac:1)
                * WEP104 (00-0f-ac:5)
                * TKIP (00-0f-ac:2)
                * CCMP-128 (00-0f-ac:4)
                * CCMP-256 (00-0f-ac:10)
                * GCMP-128 (00-0f-ac:8)
                * GCMP-256 (00-0f-ac:9)
        Available Antennas: TX 0 RX 0
        Supported interface modes:
                 * IBSS
                 * managed
                 * AP
                 * AP/VLAN
                 * monitor
                 * mesh point
        Band 1:
                Capabilities: 0x17e
                        HT20/HT40
                        SM Power Save disabled
                        RX Greenfield
                        RX HT20 SGI
                        RX HT40 SGI
                        RX STBC 1-stream
                        Max AMSDU length: 3839 bytes
                        No DSSS/CCK HT40
                Maximum RX AMPDU length 32767 bytes (exponent: 0x002)
                Minimum RX AMPDU time spacing: 2 usec (0x04)
                HT TX/RX MCS rate indexes supported: 0-7, 32
                Bitrates (non-HT):
                        * 1.0 Mbps
                        * 2.0 Mbps (short preamble supported)
                        * 5.5 Mbps (short preamble supported)
                        * 11.0 Mbps (short preamble supported)
                        * 6.0 Mbps
                        * 9.0 Mbps
                        * 12.0 Mbps
                        * 18.0 Mbps
                        * 24.0 Mbps
                        * 36.0 Mbps
                        * 48.0 Mbps
                        * 54.0 Mbps
                Frequencies:
                        * 2412 MHz [1] (20.0 dBm)
                        * 2417 MHz [2] (20.0 dBm)
                        * 2422 MHz [3] (20.0 dBm)
                        * 2427 MHz [4] (20.0 dBm)
                        * 2432 MHz [5] (20.0 dBm)
                        * 2437 MHz [6] (20.0 dBm)
                        * 2442 MHz [7] (20.0 dBm)
                        * 2447 MHz [8] (20.0 dBm)
                        * 2452 MHz [9] (20.0 dBm)
                        * 2457 MHz [10] (20.0 dBm)
                        * 2462 MHz [11] (20.0 dBm)
                        * 2467 MHz [12] (20.0 dBm) (no IR)
                        * 2472 MHz [13] (20.0 dBm) (no IR)
                        * 2484 MHz [14] (20.0 dBm) (no IR)
        Supported commands:
                 * new_interface
                 * set_interface
                 * new_key
                 * start_ap
                 * new_station
                 * new_mpath
                 * set_mesh_config
                 * set_bss
                 * authenticate
                 * associate
                 * deauthenticate
                 * disassociate
                 * join_ibss
                 * join_mesh
                 * set_tx_bitrate_mask
                 * frame
                 * frame_wait_cancel
                 * set_wiphy_netns
                 * set_channel
                 * set_wds_peer
                 * probe_client
                 * set_noack_map
                 * register_beacons
                 * start_p2p_device
                 * set_mcast_rate
                 * connect
                 * disconnect
                 * set_qos_map
                 * set_multicast_to_unicast
        Supported TX frame types:
                 * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
                 * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
                 * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
                 * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
                 * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
                 * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
                 * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
                 * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
        Supported RX frame types:
                 * IBSS: 0x40 0xb0 0xc0 0xd0
                 * managed: 0x40 0xd0
                 * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
                 * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
                 * mesh point: 0xb0 0xc0 0xd0
                 * P2P-client: 0x40 0xd0
                 * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
                 * P2P-device: 0x40 0xd0
        software interface modes (can always be added):
                 * AP/VLAN
                 * monitor
        valid interface combinations:
                 * #{ AP, mesh point } <= 8,
                   total <= 8, #channels <= 1
        HT Capability overrides:
                 * MCS: ff ff ff ff ff ff ff ff ff ff
                 * maximum A-MSDU length
                 * supported channel width
                 * short GI for 40 MHz
                 * max A-MPDU length exponent
                 * min MPDU start spacing
        Device supports TX status socket option.
        Device supports HT-IBSS.
        Device supports SAE with AUTHENTICATE command
        Device supports low priority scan.
        Device supports scan flush.
        Device supports AP scan.
        Device supports per-vif TX power setting
        Driver supports full state transitions for AP/GO clients
        Driver supports a userspace MPM
        Device supports configuring vdev MAC-addr on create.
        Supported extended features:
                * [ RRM ]: RRM
                * [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
                * [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
                * [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211

[링크 : https://unix.stackexchange.com/questions/405282/finding-capabilities-of-wifi-driver-device]

'embeded > raspberry pi' 카테고리의 다른 글

라즈베리 RC는 일단 구동에는 실패  (0) 2020.06.10
rpi / android h264 streaming  (0) 2020.05.24
hostapd 802.11n 설정하기 시도중  (0) 2020.05.16
RC카 node.js was 제작 1차 완료  (0) 2020.05.14
node.js raspi-pwm  (0) 2020.05.14
node.js onoff  (0) 2020.05.13
Posted by 구차니

댓글을 달아 주세요