'rtorrent'에 해당되는 글 1건

  1. 2012.06.07 rutorrent on ubuntu 12.04 LTS
Linux/Ubuntu2012.06.07 07:56
rutorrent는 rtorrent의 webUI GUI frontend이다.
간단하게 토런토 프로그램을 웹서버를 통해 원격에서 볼수있게 해주는 역활을 한다.

패키지 설치 및 삭제
$ sudo apt-get remove libxmlrpc-c*
$ sudo apt-get install subversion gcc apache2 curl libcurl4-openssl-dev automake autoconf texinfo libapache2-mod-scgi build-essential libtool openssl libsigc++-2.0-dev libncurses-dev libcppunit-dev php5

xmlrpc-c 다운로드 및 설치(svn)
$ svn co http://xmlrpc-c.svn.sourceforge.net/svnroot/xmlrpc-c/advanced xmlrpc-c
$ cd xmlrpc-c
$ ./configure
$ make
$ sudo make install

왜 하는진 모르겠지만 libxmlrpc 설치
$ sudo apt-get install libxmlrpc-c3-dev

아파치 모듈 삽입
$ sudo a2enmod scgi

아파치 환경설정 추가
$sudo vi /etc/apache2/httpd.conf
SCGIMount /RPC2 127.0.0.1:5000

아파치 재시작
$ sudo service apache2 restart

rtorrent 및 php5-cgi 설치
$ sudo apt-get install rtorrent php5-cgi

데몬을 위한 screen 프로그램 설치
$ sudo apt-get install screen
 
[링크 : http://s990we.com/wordpress/2010/10/install-xmlrpc-c-libtorrent-rtorrent-and-rutorrent-from-svn-2/ ] 

rtorrent에서 세션용으로 저장할 디렉토리를 생성해주고
$ cd ~
$ mkdir .rtsession

그리고 rtorrent 환경설정 파일에 각종 정보를 수정해 준다.
$ cat .rtorrent.rc 
# This is an example resource file for rTorrent. Copy to
# ~/.rtorrent.rc and enable/modify the options as needed. Remember to
# uncomment the options you wish to enable.

# Maximum and minimum number of peers to connect to per torrent.
#min_peers = 40
#max_peers = 100

# Same as above but for seeding completed torrents (-1 = same as downloading)
#min_peers_seed = 10
#max_peers_seed = 50

# Maximum number of simultanious uploads per torrent.
#max_uploads = 15

# Global upload and download rate in KiB. "0" for unlimited.
#download_rate = 0
#upload_rate = 0

# Default directory to save the downloaded torrents.
directory = /home/minimonk/다운로드

# Default session directory. Make sure you don't run multiple instance
# of rtorrent using the same session directory. Perhaps using a
# relative path?
session = /home/minimonk/.rtsession
scgi_port = localhost:5000

# Watch a directory for new torrents, and stop those that have been
# deleted.
#schedule = watch_directory,5,5,load_start=./watch/*.torrent
#schedule = untied_directory,5,5,stop_untied=

# Close torrents when diskspace is low.
#schedule = low_diskspace,5,60,close_low_diskspace=100M

# Stop torrents when reaching upload ratio in percent,
# when also reaching total upload in bytes, or when
# reaching final upload ratio in percent.
# example: stop at ratio 2.0 with at least 200 MB uploaded, or else ratio 20.0
#schedule = ratio,60,60,"stop_on_ratio=200,200M,2000"

# The ip address reported to the tracker.
#ip = 127.0.0.1
#ip = rakshasa.no

# The ip address the listening socket and outgoing connections is
# bound to.
#bind = 127.0.0.1
#bind = rakshasa.no

# Port range to use for listening.
#port_range = 6890-6999

# Start opening ports at a random position within the port range.
#port_random = no

# Check hash for finished torrents. Might be usefull until the bug is
# fixed that causes lack of diskspace not to be properly reported.
#check_hash = no

# Set whetever the client should try to connect to UDP trackers.
#use_udp_trackers = yes

# Alternative calls to bind and ip that should handle dynamic ip's.
#schedule = ip_tick,0,1800,ip=rakshasa
#schedule = bind_tick,0,1800,bind=rakshasa

# Encryption options, set to none (default) or any combination of the following:
# allow_incoming, try_outgoing, require, require_RC4, enable_retry, prefer_plaintext
#
# The example value allows incoming encrypted connections, starts unencrypted
# outgoing connections but retries with encryption if they fail, preferring
# plaintext to RC4 encryption after the encrypted handshake
#
# encryption = allow_incoming,enable_retry,prefer_plaintext

# Enable DHT support for trackerless torrents or when all trackers are down.
# May be set to "disable" (completely disable DHT), "off" (do not start DHT),
# "auto" (start and stop DHT as needed), or "on" (start DHT immediately).
# The default is "off". For DHT to work, a session directory must be defined.
# dht = auto

# UDP port to use for DHT. 
# dht_port = 6881

# Enable peer exchange (for torrents not marked private)
#
# peer_exchange = yes

#
# Do not modify the following parameters unless you know what you're doing.
#

# Hash read-ahead controls how many MB to request the kernel to read
# ahead. If the value is too low the disk may not be fully utilized,
# while if too high the kernel might not be able to keep the read
# pages in memory thus end up trashing.
#hash_read_ahead = 10

# Interval between attempts to check the hash, in milliseconds.
#hash_interval = 100

# Number of attempts to check the hash while using the mincore status,
# before forcing. Overworked systems might need lower values to get a
# decent hash checking rate.
#hash_max_tries = 10 

rutorrent를 설치해서 하는데 영 먼가 안되고 배를 째는데
[22.03.2011 17:42:45] WebUI started.
[22.03.2011 17:42:45] JS error: [http://cinemaverite.net/rutorrent/ : 1] Uncaught SyntaxError: Unexpected token <
[22.03.2011 17:42:45] Bad response from server: (200 [parsererror,getuisettings]) <?php require_once( &#39;util.php&#39; ); $s = @file_get_contents(getSettingsPath()."/uisettings.json"); if($s==false) $s = &#39;{}&#39;; if(!ini_get("zlib.output_compression")) header("Content-Length: ".strlen($s)); header("Content-Type: application/json; charset=UTF-8"); echo $s; ?>

[링크 : http://forums.rutorrent.org/index.php?topic=701.0

혹시나 해서 json이 문제인가 해서 php5-json을 해보니 php5-common으로 이미 설치 된 녀석이고
php5-cgi를 설치하고 나니 문제가 없이 되는 듯한 느낌..

그리고 그냥 실행하면 접속할 수 없다고 포트번호 확인하라는데
콘솔하나 열고 그냥 rtorrent 실행하면 문제없이 작동한다(보기에는 그렇지만)
서비스용 데몬 스크립트를 일단 똭~
사용자 계정만 수정해주고 rtorrent 환경파일만 수정해주면 될 듯?
(아직까지 데몬 스크립트는 실행이 안됨 ㅠ.ㅠ)
#!/bin/bash
#############
###<Notes>###
#############
# This script depends on screen.
# For the stop function to work, you must set an
# explicit session directory using absolute paths (no, ~ is not absolute) in your rtorrent.rc.
# If you typically just start rtorrent with just "rtorrent" on the
# command line, all you need to change is the "user" option.
# Attach to the screen session as your user with 
# "screen -dr rtorrent". Change "rtorrent" with srnname option.
# Licensed under the GPLv2 by lostnihilist: lostnihilist _at_ gmail _dot_ com
##############
###</Notes>###
##############

#######################
##Start Configuration##
#######################
# You can specify your configuration in a different file 
# (so that it is saved with upgrades, saved in your home directory,
# or whatever reason you want to)
# by commenting out/deleting the configuration lines and placing them
# in a text file (say /home/user/.rtorrent.init.conf) exactly as you would
# have written them here (you can leave the comments if you desire
# and then uncommenting the following line correcting the path/filename 
# for the one you used. note the space after the ".".
# . /etc/rtorrent.init.conf


#Do not put a space on either side of the equal signs e.g.
# user = user 
# will not work
# system user to run as (can only use one)
user="minimonk"

# system user to run as # not implemented, see d_start for beginning implementation
# group=$(id -ng "$user")

# the full path to the filename where you store your rtorrent configuration
# must keep parentheses around the entire statement, quotations around each config file
#config=("$(su -c 'echo $HOME' $user)/.rtorrent.rc")
# Examples:
config=("/home/minimonk/.rtorrent.rc")
# config=("/home/user/.rtorrent.rc" "/mnt/some/drive/.rtorrent2.rc")
# config=("/home/user/.rtorrent.rc"
# "/mnt/some/drive/.rtorrent2.rc"
# "/mnt/another/drive/.rtorrent3.rc")

# set of options to run with each instance, separated by a new line
# must keep parentheses around the entire statement
#if no special options, specify with: ""
options=("")
# Examples:
# starts one instance, sourcing both .rtorrent.rc and .rtorrent2.rc
# options=("-o import=~/.rtorrent2.rc")
# starts two instances, ignoring .rtorrent.rc for both, and using
# .rtorrent2.rc for the first, and .rtorrent3.rc for the second
# we do not check for valid options
# options=("-n -o import=~/.rtorrent2.rc" "-n -o import=~/rtorrent3.rc")

# default directory for screen, needs to be an absolute path
base=$(su -c 'echo $HOME' $user)

# name of screen session
srnname="rtorrent"

# file to log to (makes for easier debugging if something goes wrong)
logfile="/var/log/rtorrentInit.log"
#######################
###END CONFIGURATION###
#######################

PATH=/usr/bin:/usr/local/bin:/usr/local/sbin:/sbin:/bin:/usr/sbin
DESC="rtorrent"
NAME=rtorrent
DAEMON=$NAME
SCRIPTNAME=/etc/init.d/$NAME

checkcnfg() {
  exists=0
  for i in `echo "$PATH" | tr ':' '\n'` ; do
    if [ -f $i/$NAME ] ; then
      exists=1
      break
    fi
  done
  if [ $exists -eq 0 ] ; then
    echo "cannot find $NAME binary in PATH: $PATH" | tee -a "$logfile" >&2
    exit 3
  fi
  for (( i=0 ; i < ${#config[@]} ;  i++ )) ; do
    if ! [ -r "${config[i]}" ] ; then
        echo "cannot find readable config ${config[i]}. check that it is there and permissions are appropriate"  | tee -a "$logfile" >&2
        exit 3
    fi
    session=$(getsession "${config[i]}")
    if ! [ -d "${session}" ] ; then
        echo "cannot find readable session directory ${session} from config ${config[i]}. check permissions" | tee -a "$logfile" >&2
        exit 3
    fi
  done
}

d_start() {
  [ -d "${base}" ] && cd "${base}"
  stty stop undef && stty start undef
  #su -c "screen -S "${srnname}" -X screen rtorrent ${options} 2>&1 1>/dev/null" ${user} | tee -a "$logfile" >&2
  su -c "screen -S "${srnname}" -X screen rtorrent ${options} " ${user} | tee -a "$logfile" >&2
  # this works for the screen command, but starting rtorrent below adopts screen session gid
  # even if it is not the screen session we started (e.g. running under an undesirable gid
  #su -c "screen -ls | grep -sq "\.${srnname}[[:space:]]" " ${user} || su -c "sg \"$group\" -c \"screen -fn -dm -S ${srnname} 2>&1 1>/dev/null\"" ${user} | tee -a "$logfile" >&2
  for (( i=0 ; i < ${#options[@]} ; i++ )) ;  do
    sleep 3
    #su -c "screen -S "${srnname}" -X screen rtorrent ${options[i]} 2>&1 1>/dev/null" ${user} | tee -a "$logfile" >&2
    su -c "screen -S "${srnname}" -X screen rtorrent ${options[i]} " ${user} | tee -a "$logfile" >&2
  done
}

d_stop() {
  for (( i=0 ; i < ${#config[@]} ; i++ )) ; do
    session=$(getsession "${config[i]}")
    if ! [ -s ${session}/rtorrent.lock ] ; then
        return
    fi
    pid=$(cat ${session}/rtorrent.lock | awk -F: '{print($2)}' | sed "s/[^0-9]//g")
    # make sure the pid doesn't belong to another process
    if ps -A | grep -sq ${pid}.*rtorrent ; then
        kill -s INT ${pid}
    fi
  done
}

getsession() { 
    session=$(cat "$1" | grep "^[[:space:]]*session[[:space:]]*=" | sed "s/^[[:space:]]*session[[:space:]]*=[[:space:]]*//" )
    #session=${session/#~/`getent passwd ${user}|cut -d: -f6`}
    echo $session
}

checkcnfg

case "$1" in
  start)
    echo -n "Starting $DESC: $NAME"
    d_start
    echo "."
    ;;
  stop)
    echo -n "Stopping $DESC: $NAME"
    d_stop
    echo "."
    ;;
  restart|force-reload)
    echo -n "Restarting $DESC: $NAME"
    d_stop
    sleep 1
    d_start
    echo "."
    ;;
  *)
    echo "Usage: $SCRIPTNAME {start|stop|restart|force-reload}" >&2
    exit 1
    ;;
esac

exit 0

[링크 : http://ubuntuforums.org/showthread.php?t=859543]  

[링크 : http://code.google.com/p/rutorrent/wiki/Installation ]
[링크 : http://code.google.com/p/rutorrent/wiki/WebSERVER ]
[링크 : http://code.google.com/p/rutorrent/wiki/Config ] 
[링크 : http://www.howtoforge.com/installing-cherokee-with-php5-and-mysql-support-on-ubuntu-9.04 ] cherokee 
신고
Posted by 구차니

댓글을 달아 주세요