embeded/orange pi2022. 1. 1. 13:39

micro USB쪽이 GND

gnd / rx / tx

 

[링크 : http://wiki.nathael.net/index.php/Dev/OPi/OPi3]

 

전에는 안되는 것 같더니(power LED 불 안들어 왔었음)

디버그 꽂으니 감시당하는 느낌이라 잘 되는 건가?

U-Boot SPL 2019.04-armbian (Jul 06 2019 - 20:55:41 +0200)
DRAM: 2048 MiB
Trying to boot from MMC2
NOTICE:  BL31: v2.1(debug):bb2d778-dirty
NOTICE:  BL31: Built : 20:55:33, Jul  6 2019
NOTICE:  BL31: Detected Allwinner H6 SoC (1728)
NOTICE:  BL31: Found U-Boot DTB at 0xc079e78, model: OrangePi 3
INFO:    ARM GICv2 driver initialized
NOTICE:  PMIC: Probing AXP805
NOTICE:  PMIC: AXP805 detected
INFO:    BL31: Platform setup done
INFO:    BL31: Initializing runtime services
INFO:    BL31: cortex_a53: CPU workaround for 855873 was applied
INFO:    BL31: Preparing for EL3 exit to normal world                           
INFO:    Entry point address = 0x4a000000                                       
INFO:    SPSR = 0x3c9                                                           
                                                                                
                                                                                
U-Boot 2019.04-armbian (Jul 06 2019 - 20:55:41 +0200) Allwinner Technology      
                                                                                
CPU:   Allwinner H6 (SUN50I)                                                    
Model: OrangePi 3                                                               
DRAM:  2 GiB                                                                    
MMC:   mmc@4020000: 0, mmc@4022000: 1                                           
Loading Environment from EXT4... Card did not respond to voltage select!        
In:    serial@5000000                                                           
Out:   serial@5000000                                                           
Err:   serial@5000000                                                           
Net:   No ethernet found.                                                       
starting USB...                                                                 
No controllers found                                                            
Hit any key to stop autoboot:  0                                                
switch to partitions #0, OK                                                     
mmc1(part 0) is current device                                                  
Scanning mmc 1:1...                                                             
Found U-Boot script /boot/boot.scr                                              
3042 bytes read in 1 ms (2.9 MiB/s)                                             
## Executing script at 4fc00000                                                 
U-boot loaded from SD                                                           
Boot script loaded from mmc                                                     
165 bytes read in 1 ms (161.1 KiB/s)                                            
Card did not respond to voltage select!                                         
35737 bytes read in 7 ms (4.9 MiB/s)                                            
4191 bytes read in 3 ms (1.3 MiB/s)                                             
Applying kernel provided DT fixup script (sun50i-h6-fixup.scr)                  
## Executing script at 44000000                                                 
15367185 bytes read in 1553 ms (9.4 MiB/s)                                      
21860360 bytes read in 2209 ms (9.4 MiB/s)                                      
## Loading init Ramdisk from Legacy Image at 4fe00000 ...                       
   Image Name:   uInitrd                                                        
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)                  
   Data Size:    15367121 Bytes = 14.7 MiB                                      
   Load Address: 00000000                                                       
   Entry Point:  00000000                                                       
   Verifying Checksum ... OK                                                    
## Flattened Device Tree blob at 4fa00000                                       
   Booting using the fdt blob at 0x4fa00000                                     
   Loading Ramdisk to 49158000, end 49fffbd1 ... OK                             
   Loading Device Tree to 00000000490e6000, end 0000000049157fff ... OK         
                                                                                
Starting kernel ...                                                             
                                                                                
done.                                                                           
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems       
done.                                                                           
Begin: Waiting for root file system ... Begin: Running /scripts/local-block ....
done.                                                                           
Begin: Will now check root file system ... fsck from util-linux 2.33.1          
[/sbin/fsck.ext4 (1) -- /dev/mmcblk2p1] fsck.ext4 -a -C0 /dev/mmcblk2p1         
/dev/mmcblk2p1: recovering journal                                              
/dev/mmcblk2p1: clean, 145655/472352 files, 1015560/1888624 blocks              
done.                                                                           
done.                                                                           
Begin: Running /scripts/local-bottom ... done.                                  
Begin: Running /scripts/init-bottom ... done.                                   
                                                                                
Welcome to Debian GNU/Linux 10 (buster)!                                        
                                                                                
[  OK  ] Reached target Remote File Systems.                                    
[  OK  ] Created slice system-getty.slice.                                      
[  OK  ] Set up automount Arbitrary�…s File System Automount Point.             
[  OK  ] Reached target Swap.                                                   
[  OK  ] Listening on Journal Socket.                                           
         Starting Create list of re�…odes for the current kernel...             
[  OK  ] Reached target System Time Synchronized.                               
         Mounting Kernel Debug File System...                                   
         Mounting POSIX Message Queue File System...                            
[  OK  ] Listening on udev Kernel Socket.                                       
         Mounting Huge Pages File System...                                     
[  OK  ] Listening on initctl Compatibility Named Pipe.                         
[  OK  ] Listening on Journal Socket (/dev/log).                                
[  OK  ] Started Forward Password R�…uests to Wall Directory Watch.             
[  OK  ] Listening on udev Control Socket.                                      
         Starting udev Coldplug all Devices...                                  
[  OK  ] Listening on fsck to fsckd communication Socket.                       
[  OK  ] Listening on Journal Audit Socket.                                     
         Starting Restore / save the current clock...                           
[  OK  ] Created slice User and Session Slice.                                  
         Starting Remount Root and Kernel File Systems...                       
[  OK  ] Listening on Syslog Socket.                                            
         Starting Set the console keyboard layout...                            
[  OK  ] Reached target Slices.                                                 
         Starting Nameserver information manager...                             
[  OK  ] Created slice system-serial\x2dgetty.slice.                            
         Starting Load Kernel Modules...                                        
[  OK  ] Started Create list of req�… nodes for the current kernel.             
[  OK  ] Mounted Kernel Debug File System.                                      
[  OK  ] Mounted POSIX Message Queue File System.                               
[  OK  ] Mounted Huge Pages File System.                                        
[  OK  ] Started Restore / save the current clock.                              
[  OK  ] Started Remount Root and Kernel File Systems.                          
         Starting Load/Save Random Seed...                                      
         Starting Create System Users...                                        
[  OK  ] Started Nameserver information manager.                                
[  OK  ] Started Load Kernel Modules.                                           
         Mounting Kernel Configuration File System...                           
         Starting Apply Kernel Variables...                                     
[  OK  ] Started Load/Save Random Seed.                                         
[  OK  ] Mounted Kernel Configuration File System.                              
[  OK  ] Started Apply Kernel Variables.                                        
[  OK  ] Started Create System Users.                                           
         Starting Create Static Device Nodes in /dev...                         
[  OK  ] Started Create Static Device Nodes in /dev.                            
         Starting udev Kernel Device Manager...                                 
[  OK  ] Started udev Coldplug all Devices.                                     
[  OK  ] Started udev Kernel Device Manager.                                    
         Starting Helper to synchronize boot up for ifupdown...                 
[  OK  ] Started Set the console keyboard layout.                               
[  OK  ] Reached target Local File Systems (Pre).                               
         Mounting /tmp...                                                       
         Starting Show Plymouth Boot Screen...                                  
[  OK  ] Mounted /tmp.                                                          
[  OK  ] Reached target Local File Systems.                                     
         Starting Armbian ZRAM config...                                        
         Starting Tell Plymouth To Write Out Runtime Data...                    
         Starting Set console font and keymap...                                
[  OK  ] Started Helper to synchronize boot up for ifupdown.                    
[  OK  ] Started Tell Plymouth To Write Out Runtime Data.                       
         Starting Raise network interfaces...                                   
[  OK  ] Started Show Plymouth Boot Screen.                                     
[  OK  ] Started Set console font and keymap.                                   
[  OK  ] Started Forward Password R�…s to Plymouth Directory Watch.             
[  OK  ] Reached target Local Encrypted Volumes.                                
[  OK  ] Reached target Paths.                                                  
[  OK  ] Found device /dev/ttyS0.                                               
[  OK  ] Created slice system-zram\x2dsetup.slice.                              
[  OK  ] Listening on Load/Save RF �…itch Status /dev/rfkill Watch.             
         Starting Tell Plymouth To Write Out Runtime Data...                    
         Starting Show Plymouth Boot Screen...                                  
[  OK  ] Started Raise network interfaces.                                      
         Starting Load/Save RF Kill Switch Status...                            
[  OK  ] Started Tell Plymouth To Write Out Runtime Data.                       
[  OK  ] Started Show Plymouth Boot Screen.                                     
[  OK  ] Started Load/Save RF Kill Switch Status.                               
[  OK  ] Started Armbian ZRAM config.                                           
         Starting Armbian memory supported logging...                           
[  OK  ] Started Armbian memory supported logging.                              
         Starting Journal Service...                                            
[  OK  ] Started Journal Service.                                               
         Starting Flush Journal to Persistent Storage...                        
[  OK  ] Started Flush Journal to Persistent Storage.                           
         Starting Create Volatile Files and Directories...                      
[  OK  ] Started Create Volatile Files and Directories.                         
         Starting Update UTMP about System Boot/Shutdown...                     
[  OK  ] Started Entropy daemon using the HAVEGE algorithm.                     
[  OK  ] Started Update UTMP about System Boot/Shutdown.                        
[  OK  ] Reached target System Initialization.                                  
         Starting Armbian hardware optimization...                              
[  OK  ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.                
[  OK  ] Started Daily apt download activities.                                 
[  OK  ] Listening on PC/SC Smart Card Daemon Activation Socket.                
[  OK  ] Started Daily rotation of log files.                                   
         Starting Armbian hardware monitoring...                                
[  OK  ] Started Daily Cleanup of Temporary Directories.                        
[  OK  ] Started Daily apt upgrade and clean activities.                        
[  OK  ] Started Daily man-db regeneration.                                     
[  OK  ] Reached target Timers.                                                 
[  OK  ] Listening on D-Bus System Message Bus Socket.                          
[  OK  ] Reached target Sockets.                                                
[  OK  ] Started Armbian hardware monitoring.                                   
[  OK  ] Started Armbian hardware optimization.                                 
[  OK  ] Reached target Basic System.                                           
         Starting Setup zram based device zram2...                              
         Starting Resets System Activity Data Collector...                      
         Starting System Logging Service...                                     
[  OK  ] Started D-Bus System Message Bus.                                      
         Starting Network Manager...                                            
         Starting Setup zram based device zram1...                              
         Starting Modem Manager...                                              
         Starting Avahi mDNS/DNS-SD Stack...                                    
         Starting Bluetooth service...                                          
         Starting Login Service...                                              
         Starting Setup zram based device zram0...                              
[  OK  ] Started CUPS Scheduler.                                                
[  OK  ] Started Manage Sound Card State (restore and store).                   
         Starting Save/Restore Sound Card State...                              
[  OK  ] Started Regular background program processing daemon.                  
         Starting WPA supplicant...                                             
         Starting LSB: Load kernel �…d to enable cpufreq scaling...             
[  OK  ] Started System Logging Service.                                        
[  OK  ] Started Resets System Activity Data Collector.                         
[  OK  ] Started Save/Restore Sound Card State.                                 
[  OK  ] Started Setup zram based device zram2.                                 
[  OK  ] Started Setup zram based device zram1.                                 
[  OK  ] Started Setup zram based device zram0.                                 
[  OK  ] Started Login Service.                                                 
[  OK  ] Reached target Sound Card.                                             
[  OK  ] Started Avahi mDNS/DNS-SD Stack.                                       
[  OK  ] Started Make remote CUPS printers available locally.                   
         Starting LSB: SANE network scanner server...                           
[  OK  ] Started WPA supplicant.                                                
[  OK  ] Started Bluetooth service.                                             
[  OK  ] Reached target Bluetooth.                                              
[  OK  ] Started LSB: SANE network scanner server.                              
         Starting Hostname Service...                                           
         Starting Authorization Manager...                                      
[  OK  ] Started Network Manager.                                               
         Starting Network Manager Wait Online...                                
[  OK  ] Reached target Network.                                                
         Starting Permit User Sessions...                                       
         Starting OpenVPN service...                                            
         Starting Network Time Service...                                       
[  OK  ] Started OpenVPN service.                                               
[  OK  ] Started Permit User Sessions.                                          
[  OK  ] Started Authorization Manager.                                         
[  OK  ] Started LSB: Load kernel m�…ded to enable cpufreq scaling.             
         Starting LSB: set CPUFreq kernel parameters...                         
[  OK  ] Started Network Time Service.                                          
[  OK  ] Started Hostname Service.                                              
[  OK  ] Started LSB: set CPUFreq kernel parameters.                            
         Starting LSB: Set sysfs variables from /etc/sysfs.conf...              
[  OK  ] Started Modem Manager.                                                 
         Starting Network Manager Script Dispatcher Service...                  
[  OK  ] Started Network Manager Script Dispatcher Service.                     
[  OK  ] Started LSB: Set sysfs variables from /etc/sysfs.conf.                 
[  OK  ] Started Network Manager Wait Online.                                   
[  OK  ] Reached target Network is Online.                                      
         Starting /etc/rc.local Compatibility...                                
         Starting LSB: Advanced IEEE 802.11 management daemon...                
[  OK  ] Started /etc/rc.local Compatibility.                                   
[  OK  ] Started LSB: Advanced IEEE 802.11 management daemon.                   
         Starting Terminate Plymouth Boot Screen...                             
         Starting Hold until boot process finishes up...                        
                                                                                
Armbian 20.08.9 Buster ttyS0                                                    
                                                                                
orangepi3 login: root                                                           
Password:                                                                       
Last login: Sat Jan  1 13:22:47 KST 2022 on tty1                                
  ___  ____  _   _____                                                          
 / _ \|  _ \(_) |___ /                                                          
| | | | |_) | |   |_ \                                                          
| |_| |  __/| |  ___) |                                                         
 \___/|_|   |_| |____/                                                          
                                                                                
Welcome to Debian GNU/Linux 10 (buster) with Linux 5.10.60-sunxi64              
                                                                                
System load:   10%              Up time:       0 min                            
Memory usage:  5% of 1.94G      IP:            192.168.219.206                  
CPU temp:      22�°C            Usage of /:    56% of 7.1G                      
                                                                                
[ General system configuration (beta): armbian-config ]                         
                                                                                
root@orangepi3:~#

'embeded > orange pi' 카테고리의 다른 글

allwinner(orange pi 3) vs amlogic(odroid c2)  (0) 2022.01.01
orange pi 3 armbian  (0) 2022.01.01
orange pi 3 eMMC 부팅 로그  (0) 2022.01.01
orange pi 3에 이미지 업데이트  (0) 2021.12.31
orangepi-config  (0) 2021.12.31
orange pi 3, 3 lts  (0) 2021.12.31
Posted by 구차니

댓글을 달아 주세요